SEOWOO GNC · FIRE PROTECTION

내화충진재 시스템

FIRE-RESISTANT FIRESTOP SYSTEM

방화구획의 약점인 설비 관통부 틈새를 막아,
화염·연기·독성가스의 확산을 차단합니다.Seals service-penetration gaps in fire compartments to help stop the spread of flames, smoke and toxic gases.

SYSTEM PRODUCT LINE-UP

관통부 조건에 맞춘
내화충진 구성 제품

덕트형 내화충진 구조와 설비별 ABS 고정구를 현장 조건에 맞춰 구성합니다.Firestop duct assemblies and ABS fixtures are configured for each penetration and service condition.

덕트 관통부용 내화충진 구조 제품함석마감재GALVANIZED SHEET FINISH세라믹섬유블랭킷CERAMIC FIBER BLANKET방화댐퍼FIRE DAMPER내화채움재FIRESTOP INFILL단열재 고정핀INSULATION ANCHOR PIN
DUCT SYSTEM

내화충진 구조 · 덕트형FIRESTOP DUCT ASSEMBLY

방화댐퍼와 함석마감재, 세라믹섬유블랭킷 및 내화충진재를 일체로 구성해 덕트 관통부의 틈새와 열 이동을 제어합니다.Combines the fire damper, galvanized finish, ceramic-fiber blanket and firestop infill to control gaps and heat transfer around duct penetrations.

소방, 난방, 급수·급탕 설비용 ABS 고정구 일체형 제품
소방FIRE난방HEATING급수·급탕WATER SUPPLY / HOT WATER
ABS INTEGRATED FIXTURE

ABS 고정구 일체형ABS FIRESTOP FIXTURE

소방·난방·급수·급탕 설비 구분에 맞춘 세 가지 고정구로 내화충진 구조의 설치 구분과 제품 구성을 명확하게 관리합니다.Three fixture types support clear product selection and installation for fire, heating, water-supply and hot-water services.

01 / WHY IT MATTERS

방화구획은 견고하지만,
관통부 틈새는 열려 있습니다.

건축·설비 시공에서 벽과 바닥을 가로지르는 덕트·배관·케이블은 방화구획을 관통합니다. 이때 생긴 틈새는 화재 시 화염과 연기, 독성가스가 빠르게 이동하는 통로가 될 수 있습니다.Ducts, pipes and cables penetrate fire compartments. If the remaining gaps are not properly sealed, they can become direct paths for flames, smoke and toxic gases.

01

화염FLAME

고온의 화염이 덕트 내부로 전파되며 인접 구역의 가연물을 순차적으로 점화시킵니다.Flames can travel through an unsealed opening and ignite combustible materials in adjacent compartments.

02

연기SMOKE

연기가 틈새를 따라 빠르게 확산되면 대피 시야를 가리고 질식 위험을 높입니다.Smoke spreading through gaps reduces evacuation visibility and rapidly increases inhalation risk.

03

독성가스TOXIC GAS

일산화탄소와 HCN 등 연소가스가 인접 공간으로 유입되어 인명 피해를 키울 수 있습니다.Combustion gases such as carbon monoxide and HCN can enter adjoining spaces and intensify life-safety hazards.

ESSENTIAL PERFORMANCE

틈새를 밀폐해
확산 경로를 끊습니다.

화염 차단FIRE BLOCKING차열HEAT BLOCKING차염SMOKE BLOCKING

02 / SYSTEM COMPONENTS

내화충진구조 시스템
부위 구성

방화구획 관통부의 구조와 설비 종류를 확인한 뒤, 덕트와 배관 주변을 구성 재료로 밀폐하고 견고하게 고정합니다.After reviewing the penetration and service type, the system seals and secures the area around ducts and pipes with coordinated firestop components.

화염 구역과 안전 구역을 방화벽·덕트·배관 내화충진구조로 분리한 단면도
01

함석마감재GALVANIZED SHEET FINISH

아연도금 철판으로 단열재와 벽체 접합부를 마감하고 이탈을 방지합니다.Finishes the insulation-to-wall joint with galvanized sheet metal and prevents separation.

02

세라믹섬유블랭킷CERAMIC FIBER BLANKET · 50T × 1,000mm

두께 50mm의 내화 단열재를 벽체 양측에 시공해 열전도를 억제합니다.A 50 mm fire-resistant blanket is installed on both sides to reduce heat transfer.

03

방화댐퍼FIRE DAMPER · 500mm APPLICATION

덕트 관통부의 중심에서 화재 시 자동으로 폐쇄되어 화염 이동을 차단합니다.Automatically closes at the duct penetration to interrupt flame movement during a fire.

04

내화충진재FIRESTOP INFILL

발포스트립과 세라믹섬유 재료로 벽체와 덕트 사이의 틈새를 빈틈없이 밀폐합니다.Foam strip and ceramic-fiber material tightly seal the gap between the wall and duct.

05

단열재 고정핀INSULATION ANCHOR PIN

덕트와 배관 외부에 단열재를 견고하게 고정해 시공 상태를 유지합니다.Securely anchors insulation around ducts and pipes to maintain the installed condition.

03 / SEOWOO PROCESS

현장 맞춤
시공 프로세스

주식회사 서우지앤씨는 일률적인 사양 적용이 아니라, 관통부 구조와 현장 조건을 확인한 뒤 필요한 시스템을 설계하고 시공합니다.SEO WOO GNC reviews each penetration and site condition before detailing and installing the appropriate firestop system.

상담CONSULT

01

현장 조건과 도면, 요구 성능을 함께 검토해 적용 방향을 정합니다.Review site conditions, drawings and required performance.

현장 검토SITE REVIEW

02

관통부 위치와 규격, 구조 및 적용 재료를 현장에서 직접 확인합니다.Confirm penetration location, size, structure and materials on site.

맞춤 설계CUSTOM DETAIL

03

현장 상황에 맞춘 내화충진 상세와 부위별 시공 방법을 결정합니다.Define site-specific firestop details and installation methods.

시공·검증INSTALL · VERIFY

04

시공 후 마감과 충전 상태를 점검하고 요구 성능을 확인합니다.Inspect finish and infill conditions after installation.